Feedback Tab

How to Install


Corbels & Brackets

Once you have selected your corbel or bracket and determined its usage, you must now decide how to hang it. This can be done in several ways and is determined by (1) the location of the installation, and (2) the sort of load it is going to be carrying. The easiest and more common method is to hang the corbel if the overall weight is not too heavy. Hard mounting with screws or bolts will be necessary if the corbel or bracket is providing significant support for the structure.

Final Installed Corbel
HANGING A CORBEL

HANGING A CORBEL

All corbels from Van Dykes will have a keyhole slot routed directly into the back of the corbel with most having a metal piece for reinforcement. Corbels will have one or two keyhole notches depending on the size of the piece. Larger pieces will have three notches.

First, measure the back of the corbel from the top of the corbel to the highest points of the narrow ends of the keyhole slots. Next, mark these measurements on the surface where you will mount the corbel.

SELECTING THE SCREWS

When choosing screws, you will want to select a screw with a head size that the slot will accommodate. The length of the screw will be determined by the surface you are affixing the corbel to and by the weight you need to support. Anchors may be necessary if you will be hanging the corbels in sheetrock and there are no wall studs in the area you will hang the corbel.
SELECTING THE SCREWS
FRONT MOUNTING A CORBEL

HARD MOUNTING A CORBEL

Hard mounting has its obvious advantages and can be done from the front or back.

To mount the corbels from behind, use multiple screws or bolts that are long enough to enter the corbel but not so long as to go all the way through the corbel.

If you can't attach a corbel from the back, a front mount is required. You can simply screw into the front of the corbel and cover the screw heads with putty and sand. Be aware of what you are screwing into and make sure you are going at least 1 1/2" into the mounting surface. Use enough screws to keep the corbel firmly in place.

You may also use wood glue along with the screws when hard mounting, but this can ruin your surface if you ever have to remove the corbel.

How to Install


Corbels & Brackets

Final Installed Corbel
Once you have selected your corbel or bracket and determined its usage, you must now decide how to hang it. This can be done in several ways and is determined by (1) the location of the installation, and (2) the sort of load it is going to be carrying. The easiest and more common method is to hang the corbel if the overall weight is not too heavy. Hard mounting with screws or bolts will be necessary if the corbel or bracket is providing significant support for the structure.

HANGING A CORBEL

All corbels from Van Dykes will have a keyhole slot routed directly into the back of the corbel with most having a metal piece for reinforcement. Corbels will have one or two keyhole notches depending on the size of the piece. Larger pieces will have three notches.

First, measure the back of the corbel from the top of the corbel to the highest points of the narrow ends of the keyhole slots. Next, mark these measurements on the surface where you will mount the corbel.
HANGING A CORBEL

SELECTING THE SCREWS

When choosing screws, you will want to select a screw with a head size that the slot will accommodate. The length of the screw will be determined by the surface you are affixing the corbel to and by the weight you need to support. Anchors may be necessary if you will be hanging the corbels in sheetrock and there are no wall studs in the area you will hang the corbel.
SELECTING THE SCREWS

HARD MOUNTING A CORBEL

Hard mounting has its obvious advantages and can be done from the front or back.

To mount the corbels from behind, use multiple screws or bolts that are long enough to enter the corbel but not so long as to go all the way through the corbel.

If you can't attach a corbel from the back, a front mount is required. You can simply screw into the front of the corbel and cover the screw heads with putty and sand. Be aware of what you are screwing into and make sure you are going at least 1 1/2" into the mounting surface. Use enough screws to keep the corbel firmly in place.

You may also use wood glue along with the screws when hard mounting, but this can ruin your surface if you ever have to remove the corbel.
FRONT MOUNTING A CORBEL